|

Share:


PFA PRESS FORCE ANALYZER

Contact Us

Quantity:

PFA is an all-purpose type controller that can perform motor control & OK/NOK judgement at the same time!
Sequence can be setup with easy touch panel operation while changing test condition.
Various judgement functions such as waveform judgement by 2 dimensions including “Force vs. Displacement” or “Torque vs. Angle” are mounted, which manages tests inclusively.
Can be cooperated with external peripheral devices & can perform continuous tests independently, thus can construct testing device, pressing machine & screw tightening device etc. without PLC.
Enables high speed press without overshooting.


PFA monitors press process by waveform
DO NOT miss NOK workpieces
Servo motor controller is equipped. Even beginner of motor control can create simple sequence by using touch panel setup.
 


OK/ NOK judgement with 2 sensor inputs
Two-dimensional OK/NOK judgement can be performed with force (Y axis) and time/ displacement (X axis)
 
 
Comparison & hold function from waveform display
Reputable judgement algorithm of F381A and FS2000 is programmed.
 
■Waveform comparison judgment
The function compares the actual measurement waveform against the setup High/Low limit waveforms.
It will give out an NOK judgement when any of the point exceeded the present High/Low limit waveforms.


■Multi-point judgment
OK/NOK judgement can be performed on multi points in one process. (e.g. The start point and end point of press fitting can be judged respectively.) (Max. 5 points)


Easy for communication with a host
Results and waveforms can be uploaded to host over the network.
Also, judgement switching and monitoring can be done remotely from the host.
Measurement data and set values can be recorded into SD card.
 
Preventive maintenance with trend display
Can detect abnormalities quickly & prevent malfunction by using trend display to monitor changes of zero point, hold values, etc.
Using master as reference, you can see directly the difference by comparing to a commissioned machine.
 
Motor control function
Motor control uses versatile pulse input/output.
Compatible with various motors.

Templates are available for frequently used sequence.
Press behavior can be decided by inputting speed, position, and other parameters.



Screw tightening management template compliant to torque method & turning angle method is also available.
Can be used as controllers for tension & compression test machines, bending testing machine & endurance test machine as well.

Sensor input
Fixed as strain gauge input(6-wire)
Excitation voltage DC2.5, 5, 10V±10%(depending on settings)
Output current: Within 30mA
Signal input range -2.0mV/V to +2.0mV/V
Accuracy Non-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input)
Zero drift: Within 0.2μV/℃ RTI
Gain drift: Within 15ppm/℃
Low-pass filter Selectable from 2 to 2kHz(-6dB/oct.)
A/D converter Speed: 5000 times/sec.
Resolution: 24bit (binary)
Voltage input
Signal input range -10 to +10V
Input impedance App. 1MΩ or more
Accuracy Non-linearity:Within 0.02%/FS ±1 digit (at 10V input)
Zero drift:Within 0.2mV/℃ RTI
Gain drift:Within 0.01%/℃
Low-pass filter Selectable from 2 to 2kHz(-6dB/oct.)
A/D converter Speed: 5000 times/sec
Resolution:24bit Effective
Sensor input Sensor input for displacement
Pulse input (Line driver)
Max. input frequency 1MHz
Internal count range 30bit
Adaptable rotary encoder Output: Incremental type 2-phase output (A/B signal output)
Output stage circuit specification:Line driver (based on RS-422A)
Analog voltage output
Output level Approx. 2V per 1.0mV/V input
Load resistance 2kΩ or more
 

 

Display section
Display 7.0 inch TFT color LCD module
Display section Display area: 152(W)×91(H)mm
Dot configuration: 800×480 dot
Language:Japanese, English, Chinese
 
COMP. & JUDGE. function
Multi point comparison mode
256ch
(setting values can be stored)
Capable of judging up to 5 hold points at the same time.
Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End
Waveform comparison mode
256ch
(setting values can be stored)
Compares the actually measured waveform against the preset Hi/Lo waveforms.
The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK.
 
Preventive maintenance support
Trend display Trend analysis of measured data & detect irregularities at early stage.
Statistics Takes judgement results of latest data (10,000)
Displays measurement count, OK/NOK ratio
Screen capture Saves screen capture data as bmp data.
Editable work name Work name can be edited and displayed for each Work No..
Setting list display Distinguish master setting & current setting with color.
User management Register multiple login IDs and password
 
External signal
Output signal
16 points
Hold judgement (force, stroke)/ Force overload/ Measurement complete/ Waveform comparison/ Force・stroke OK/ CPU OK/ SD card OK/ Timing output 1,2/ Servo ready/ Motor alarm/ In position/ Brake off/ Torque limit/ Zero speed/ General-purpose output/ Sequence in progress/ Return origin complete/ POT(Forward rotation lock)/ NOT(Reverse rotation lock)
*Selectable from the above
Output type: select PNP or NPN (Need to specify)
Rated voltage: 30V, Rated current: 30mA
Input signal
16 points
Force zero/ Stroke adjust/ Measurement start/ Measurement stop/ HOLD 1 to 5/ Reset/ Backlight forced ON/ Touch panel lock/ Work selection/ Servo on/Start sequence/Stop sequence/Pulse clear/Alarm clear/ Forward rotation lock/Reverse rotation lock/General-purpose input/ Home position detect/Return to home position/Home position/ JOG+/ JOG-/ STEP+/ STEP-
*Selectable from the above
Input type: select PNP or NPN (Need to specify)
 
Motor control
Compatible servo amplifier Require pulse input.
Sequence function Configurable press-sequence in PFA
Switchable control modes in sequence
Control program 256 presets
(Setting values can be stored)
Up to 100 lines can be registered into 1 control program
PFA <=> Servo amplifier connection Pulse for position control (Line driver) (based on RS-422A)
Max 500k Pulse/sec
Digital I/O: Control usage
Command Motor operation:Position control / Force control/ Stand-by/ keep
Control character:Blank/ Jump/ If/ Watch/ Out put/ Judge/ Timer/ Counter
Graph:Graph color display/ Delete graph
Record:Start measurement/ Stop measurement/ Start hold/ Stop hold
Motor parameter:Speed/ Position gain/ Force gain
Row:Insert above/ Insert below/ Delete row
Digital offset:X/Y
 
External devices
Barcode Reader(USB) Scan items
SD Card Measured data・waveform can be saved (CSV)
 
Interface
Only one option can be installed.
USB USB interface
ETN Ethernet interface (option)
ODN DeviceNet interface (option)
CCL CC-Link interface (option)
EIP EtherNet/IP interface (option)
 
General performance
Power supply voltage DC24V(±15%)
Power consumption 20W typ.
Operation condition Operation temperature: -10℃ to +40℃/ Storage tempe
rature: -20℃ to +60℃
Humidity: 85% RH or less (non-condensing)
Dimensions 218(W)x 140(H)x 87(D) mm (Projections excluded)
Weight Approx. 1.8kg
CE marking certification EMC Directives EN61326-1
 
Attachments
Analog connector 1
SD card 16GByte 1
Operation manual 1
DeviceNet connector (when DeviceNet option is selected)) 1
CC-Link connector (when CC-Link option is selected) 1
 

Option

Model
ODN DeviceNet interface
CCL CC-Link interface
EIP EtherNet/IP interface
ETN Ethernet interface
 

Optional accessories

Model
SD16G SD card 16GByte
SD32G SD card 32GByte
PFA-ST Supporting stand (VESA 100/75 compliant)
PAF-CONV-PAN Dedicated terminal block
PFA-CONV-MIT Dedicated terminal block
PFA-CONV-YAS Dedicated terminal block
PFA-CONV-TAM Dedicated terminal block
PFA-CONV-SIE Dedicated terminal block
CA10-USB USB Cable( A-microB type) 1.2m
CAPF-I/O-S1M 36p 1m cable with bare wires
CAPF-I/O-S3M 36p 3m cable with bare wires
CAPF-SER-S1M 50p 1m cable with bare wires
CAPF-SER-S3M 50p 3m cable with bare wires
CAPF-I/O-W1M 36p 1m cable with connector at both ends
CAPF-I/O-W3M 36p 3m cable with connector at both ends
CAPF-SER-W1M 50p 1m cable with connector at both ends
CAPF-SER-W3M 50p 3m cable with connector at both ends
CAPF-CON-W1M 50p 1m cable with connector at both ends
CAPF-CON-W3M 50p 3m cable with connector at both ends
CN71 CC-Link connector
CND01 DeviceNet connector

Structure of product code



iMS Motion Solution (Johor) Sdn Bhd (Company Registration 1098771-W)
 
No.7, Jalan Sasa 4,Taman Gaya, 81800 Ulu Tiram, Johor Bahru, Johor. Malaysia.
TEL:+607-8635240 FAX: +607-8637240
MOBILE: +6019-6774477
EMAIL: info@ims.com.my | WhatsApp  | www.ims.com.my
HOTLINE : 1700-818-330
whatsapp us now !

Brand Name
MEISTER | GGM | Sanyo Denki | ElectroCraft | EDrive | SHIHLIN ELECTRIC | AUTONICS | UI Robot | Mitsubishi CNC | PANASONICApex Dynamics | NISSEI GTR | UNIPULSE | CREVIS
 
MOTION DEVICES SPECIALIST | SYSTEM and CONTROL INTEGRATION |
| Induction Motor | Speed Control Motor | Reversible Motor |Brake Motor |BLDC Motor |DC Motor |Planetary Gear Motor | Servo Motor | Stepping Motor | Linear Actuator Motor | Lead Screw Motor|Close Loop Stepping Motor | Customization Motors | Right Angle Gear Head | Precision Gear Reducer |PLC | Motion Controller |HMI /Touch Screen| Inverter |CNC Controller |Multi Axis Robots |IPC | SCADA |Monitoring Software | Embeded PC | Remote IO |TPC | Motion Card | Loadcell |PPC |
 
Return / Refund Policy : 
All goods sold are not returnable & we accept goods ex-change with equal or lower value of good purchased. If the ex-change items are higher than purchased items, buyer shall top up the differential cost. All payment made are not refundable, please confirm the purchase items code & cost with our sales representative before place orders.
 
Shipping and Fulfillment :
Thank you for your purchase. Once we have confirmed your payment, we will prepare and ship out your order out within 24-48 hours.( For ex-stock items only, Indent items subject to delivery stated in quotation & conversation in emails). Once your order has been shipped out, you will receive an email notification with the tracking number and tracking details inside.
 
Private Policy
General Statement of Principles 
As described in detail below, any information we gather at this web site is strictly for our use and is not shared with any other entity, public or private, for any reason - period. We will not sell or give away any lists or other data that we may retain and we do not purchase such information from other sources.
Statistical Data 
Our servers (as most) track IP addresses and referring pages to help with site maintenance and improvements. This data is viewed only as anonymous statistics to show the busiest times of the day or week, pages with errors and how effective our advertising has been. This information is not used for any other purpose.
Personal Information Collected - Order Forms
With the exception of credit card info, we store the information from your order form to allow us to track consulting issues or refer to a previous order to help provide some customer service. You may elect to have your information completely removed from this system by e-mailing us at info@ims.com.my with your request. We do not store any type of sales information.
Information Correction or Removal 
If you wish to correct, update or remove any information about you that may be in our records, please send us e-mail at info@ims.com.my with the details of your request. If you wish to contact us further, please find complete contact information on our contact page.
Cookies
Cookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a web site and stored on your computer's hard drive. We use 'cookies' to store your cart contents for you. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent. However, if you do not accept cookies, you may not be able to use the checkout section of our site.
 
Changes To This Privacy Policy
This Privacy Policy is effective as of 1st Jan 2019 and will remain in effect except with respect to any changes in its provisions in the future, which will be in effect immediately after being posted on this page.


 

Specifications

Sorry, currently do not have any product specifications
Sorry, currently do not have any video uploaded.
Sorry, currently do not have any file for download.